PLM17-WSb
Product Description
Application
Dimensions and Tolerances
Dimensions | Tolerances | |
Length | 500m | ±5m |
Width | 1.25m | ±5mm |
Thickness | 0.07mm | ±0.005mm |
Weight | 65KG | ±5KG |
Other dimensions could on your request |
Polyma decorative film testing standard:
Surface Quality Standard
Description | Size of Defect | Results |
Corrugation | Not obvious | |
Bubbling | ≤5mm | Not more than 1 occurrence per m2 |
Flaw | ≤3mm | Not more than 3 occurrences per m2 |
Scoring | ≤100mm | Not more than 3 ocurrences per 500m |
Scratch | ≤300mm2 | Not more than 3 ocurrences per 500m |
Compliance Table
Description | Standard | Results |
Composite film thickness (um) | GB/T 6672 | ≥65 |
Film width (m) | GB/T 6673 | 1.03/1.25/1.30 |
Film length (m) | GB/T 6673 | 500/1000 |
Pencil Hardness | GB/T 6639 | ≥HB |
Adhesion | GB/T 9286,GB/T 1720 | Not lower than level 1 |
Withstand impact | GB/T 1732 | 50 kg.cm no shad / crack |
Film elasticity (Mpa) | GB/T 13022 | ≥200 |
Film break point (%) | ≥120 | |
180℃Degree Peeling Strength (N/mm) | GB/T 2790 | ≥2 |
Heat Difference Resistance | GB/T 17748 | No effect |
Boiling Water Resistance | GB/T 17748 | No effect |
Chemical Resistance | ||
Acid | GB/T 17748 | No effect |
Alkaline | GB/T 17748 | No effect |
Oil | GB/T 17748 | No effect |
Solvent | GB/T 17748 | No effect |
Washing | GB/T 9266 | No effect over 10,000 times |
Certificate
Recommended pattern
Niches
Why choose us?
Raw material:
1-Ink
Features:
2-Glue
Features:
Good adhesion, no bubble
3-PET film
Features:
Machine
1-We could improve the sharpness and clarity of patterns, also could create new colors which are difficult to customized.
2-Laminating machine, length is over 30m, which adopts closed loop and automatic tension control system, net-like rubber roll gluing and 25m oven. It make sure that the chemical residues of decorative film are lower than American standard.
3-Two 30㎡ oven. All finished products will be put in oven at least 72 hours to lower the chemical residues again and dry the glue.
QC
Testing before production:
1-Every batch of raw material will be tested.
2-All colors match by America X-Rite Color Master
Testing during production:
Testing after production:
Certificate
Raw material:
1-Ink
Features:
Uniformity color
Temperature resistance
2-Glue
Features:
Good adhesion, no bubble
3-PET film
Features:
Excellent physical properties, chemical properties.
Uniformity of thickness.
Machine
1-We could improve the sharpness and clarity of patterns, also could create new colors which are difficult to customized.
2-Laminating machine, length is over 30m, which adopts closed loop and automatic tension control system, net-like rubber roll gluing and 25m oven. It make sure that the chemical residues of decorative film are lower than American standard.
3-Two 30㎡ oven. All finished products will be put in oven at least 72 hours to lower the chemical residues again and dry the glue.
QC
Testing before production:
1-Every batch of raw material will be tested.
2-All colors match by America X-Rite Color Master
Testing during production:
QC will inspects product on production line every hour.
Testing after production:
1-Samples of every batch product will undergo 2 hours in boiling water test.
2-Samples of every batch product will undergo punching test for checking stretching and adhesion properties.
3-Polyma decorative film was certificated by ISO9001:2008 and Reach163.
Certificate
Lamination Illustration
Lamination Process
The metal underneath the color film should be clean, oil free, moisture free as well as dust free before the color decorative film is laminated onto it. The production parameters for the lamination process may vary due to the variation of the bonding surface. Below is the picture of lamination process.
The metal underneath the color film should be clean, oil free, moisture free as well as dust free before the color decorative film is laminated onto it. The production parameters for the lamination process may vary due to the variation of the bonding surface. Below is the picture of lamination process.